Melt Pump
- Polymer extrusion melt gear pump
- melt pump for plastic extrusion
- Polymer Reaction Kettle pump
- gear pump rubber extruder
- melt pumps for extrusion
- Melt Gear Pumps for BOPP Films
- ZB-G bearing external melt pump
- melt pump for pvc extrusion
- ZB double shaft drive melt pump
- Explanation of terms for melt pump d
- ZB-X Series chemical gear melt pump
- PID Control System for extrusion
- PLC Control System for extruder
- ZB-U series melt extrusion spinning
- ZB-E series transfer melt pump for e
- ZB-H series high temperature and hig
- ZB-R series gear melt pump for rubbe
- ZB-K series chemical stainless steel
- ZB-D series pipeline melt pump for p
- ZB-F series melt pump for reaction k
- ZB-B series dosing standard thermopl
- ZB-C series plastic granule machine
Screen Changer
- polymer melt filtration screen changer
- recycled plastic screen changer
- slide plate screen changer
- pillar screen changer
- dual bolt screen changer
- continuous screen changer
- screen changer polymer filter
- Plastic extruder filter extrusion sc
- Biodegradable plastic PBAT/PLA hydra
- Single plate hydraulic screen change
- plastic extrusion screen changer
- single plate hydraulic quick screen
- Manual control screen changer
- Double plate continuous hydraulic sc
- Automatic mesh belt continuous scree
- Double piston four screen cavities c
- Single plate double screen cavities
- Single piston double screen cavities
- Double piston four screen cavities b
- Dual Bolt double screen cavities hyd
Feeding System
- force feeder extruder
- loss in weight feeder for masterbatc
- continuous feeding system
- Liquid loss in weight feeder
- china volumetric screw doser feeder
- Multi-component loss in weight feede
- Micro loss in weight metering feeder
- Single screw gravimetric dosing feed
- Twin screw loss in weight metering f
melt blown progress
contact us
- Batte Machinery Zhengzhou Co., Ltd.
- E-mail: sale@meltpump.com
- whatsapp: +86 158 38331071
- Tel: +86-371-67991755 / 67992755
- FAX:+86-371-67993277
- Address:No.11 Changchun Road, High-tech Zone, Zhengzhou, China.
News
- The control of the melt pump speed n
- Introduction to the Basic Structure
- Analysis of the Structure and Functi
- Application, Structure, and Technica
- Melt Pump: The Secret Weapon on the
- What are the roles of the metering p
- Structure, Performance, and Applicat
- dual-column screen changer in the me
- Screen Changer Selection Strategy Ba
- Relationship Between Melt Pumps and
How to debug the melt pump of rubber and plastic extrusion production line after installation?
Zhengzhou batnei is a professional melt pump manufacturer. The melt pumps provided are widely used in the extrusion molding of plastic, resin, rubber and chemical fiber products. After the installation and parameter setting of the melt pump of the plastic extrusion production line, the system can be put into operation. This article will specifically introduce some steps and details of subsequent commissioning after the installation of the melt pump.
1. The pump body, and the pump body rear section of the melt pump are preheated.
2. After the temperature of the melt pump reaches the set temperature, remove the cover of the motor fan, turn the fan blade manually to drive the melt pump to rotate. It is normal if there is no jam, no abnormal sound and smooth rotation.
3. Then the automatic knob of the handle is kept in the manual state.
4. Adjust the frequency of the melt pump to about 5Hz and the main engine to about 3Hz. Increase the frequency of the main engine to about 0.5Hz and stop for a while. The inlet pressure changes can be seen from time to time.
5. When the pressure reaches the set pressure, let it stabilize, and then cut it into automatic mode.
6. After the main machine is automatic, slowly increase the frequency of the melt pump pump, about 1Hz at a time, until the feeding of the die is met.
7. During the test run, pay attention to the changes of various parameters. If there is any abnormality, please turn off the automatic control state. Check the causes and eliminate them in time. In case of emergency, press the emergency stop button to stop the system.
8. Please refer to the commissioning Manual of Zhengzhou Batte melt pump for detailed use.
During the actual operation, the customer must pay attention to the startup sequence: start the pump first, and then start the main motor (generally the extruder motor). Shutdown sequence: turn off the main motor first and then the pump. Zhengzhou Batte is a professional melt gear pump manufacturer in China, which can provide melt gear pump products of different specifications and models to meet the production requirements of different working conditions; Drive system, control system, screen changer and feeder can also be selected according to user requirements. info@battemachinery.com
Previous：Maintenance and parts supply of imported melt pumpNext：PET & PA industry melt discharge gear pump and plunger type double channel screen changer