Melt Pump
- Polymer extrusion melt gear pump
- melt pump for plastic extrusion
- Polymer Reaction Kettle pump
- gear pump rubber extruder
- melt pumps for extrusion
- Melt Gear Pumps for BOPP Films
- ZB-G bearing external melt pump
- melt pump for pvc extrusion
- ZB double shaft drive melt pump
- Explanation of terms for melt pump d
- ZB-X Series chemical gear melt pump
- PID Control System for extrusion
- PLC Control System for extruder
- ZB-U series melt extrusion spinning
- ZB-E series transfer melt pump for e
- ZB-H series high temperature and hig
- ZB-R series gear melt pump for rubbe
- ZB-K series chemical stainless steel
- ZB-D series pipeline melt pump for p
- ZB-F series melt pump for reaction k
- ZB-B series dosing standard thermopl
- ZB-C series plastic granule machine
Screen Changer
- polymer melt filtration screen changer
- recycled plastic screen changer
- slide plate screen changer
- pillar screen changer
- dual bolt screen changer
- continuous screen changer
- screen changer polymer filter
- Plastic extruder filter extrusion sc
- Biodegradable plastic PBAT/PLA hydra
- Single plate hydraulic screen change
- plastic extrusion screen changer
- single plate hydraulic quick screen
- Manual control screen changer
- Double plate continuous hydraulic sc
- Automatic mesh belt continuous scree
- Double piston four screen cavities c
- Single plate double screen cavities
- Single piston double screen cavities
- Double piston four screen cavities b
- Dual Bolt double screen cavities hyd
Feeding System
- force feeder extruder
- loss in weight feeder for masterbatc
- continuous feeding system
- Liquid loss in weight feeder
- china volumetric screw doser feeder
- Multi-component loss in weight feede
- Micro loss in weight metering feeder
- Single screw gravimetric dosing feed
- Twin screw loss in weight metering f
melt blown progress
contact us
- Batte Machinery Zhengzhou Co., Ltd.
- E-mail: info@battemachinery.com
- whatsapp: +86 158 38331071
- Tel: +86 371 67991755
- After-sales Tel: +86 371 67997677 / 67997877
- Address:No.11 Changchun Road, High-tech Zone, Zhengzhou, China.
News
- What materials are mainly used with
- Melt Pump for PC Lampshade Extrusion
- introduction to the application scen
- Plastic Melt Pump for Wire and Cable
- Plastic Extrusion Melt Pump for Wove
- Plastic bottle cap extrusion melt pu
- BATTE melt pump is used in the PP ya
- BATTE melt pump is used in PUR hot m
- PP Modified Granulation Dual-Column
- PET filament extrusion melt pump
How to solve the vibration noise of the melt gear pump?
When we find that the suction viscosity of the equipment is too high, the root cause may be that the medium viscosity is too thick, leading to poor flow. To effectively solve this problem, we can take measures to reduce viscosity, such as adding diluents or heating media to enhance its fluidity, thereby improving the efficiency of the equipment.
If the wear clearance of the bearings is too large, the operation of the equipment will be seriously affected. In order to restore the normal operation of the equipment, we need to replace severely worn bearings in a timely manner. Choosing high-quality new bearings and installing them correctly can ensure the stability and safety of the equipment.
The parallelism between the driving gear and the driven gear is out of tolerance, or the coaxiality between the driving gear and the motor shaft is out of tolerance, which are common causes of equipment failure. To address these issues, we need to accurately calibrate the gears to ensure correct meshing between them and avoid the occurrence of faults.
When debris enters the pump, it can seriously affect the normal operation of the pump. To solve this problem, we need to promptly clean the debris inside the pump and check the performance of the filter to ensure that impurities cannot enter the pump again.
Gear wear is also one of the common faults. For gears with severe wear, we need to repair or replace them in a timely manner to ensure the meshing accuracy and transmission efficiency of the gears.
Problems such as damaged keyways or loose fit usually require repair or replacement of corresponding components. The resolution of these issues can restore the normal working state of the equipment and avoid further damage.
Loose anchor bolts are also a common fault point. For this situation, we need to tighten the bolts in a timely manner to ensure the stability of the equipment.
If the device inhales air, its working efficiency will be greatly reduced. To solve this problem, we need to promptly discharge air, check the sealing of the equipment, eliminate air leakage, and ensure the normal operation of the equipment.
Email: info@battemachinery.com
WhatsApp: +86 158 38331071
Previous：Do you understand the application, characteristics, functions, and parameters of plastic extruder meNext：Working principle and application field of dual channel plate non-stop screen changer