- melt pump for plastic extrusion
- Polymer Reaction Kettle pump
- gear pump rubber extruder
- melt pumps for extrusion
- melt pump for pvc extrusion
- ZB double shaft drive melt pump
- Explanation of terms for melt pump d
- ZB-X Series Chemical pump
- PID Control System for extrusion
- PLC Control System for extruder
- ZB-U series gear metering spinning p
- ZB-E series pressurized melt pump fo
- ZB-H series high temperature and hig
- ZB-R series gear melt pump for rubbe
- ZB-K series polymer melt pump for re
- ZB-D series extruding pump for polym
- ZB-F series melt pump for reaction k
- ZB-B series dosing melt pump for hig
- ZB-C series plastic melt pump extrud
- recycled plastic screen changer
- slide plate screen changer
- pillar screen changer
- dual bolt screen changer
- continuous screen changer
- screen changer polymer filter
- Biodegradable plastic PBAT/PLA hydra
- Single plate hydraulic screen change
- plastic extrusion screen changer
- hydraulic slide-plate screen changer
- Manual control screen changer
- Double plate continuous hydraulic sc
- Automatic mesh belt continuous scree
- Double piston four screen cavities c
- Single plate double screen cavities
- Single piston double screen cavities
- Double piston four screen cavities b
- Dual Bolt double screen cavities hyd
- force feeder extruder
- continuous feeding system
- Liquid loss in weight feeder
- Volumetric Feeder
- Multi-component loss in weight feede
- Micro loss in weight metering feeder
- Single screw gravimetric dosing feed
- Twin screw loss in weight metering f
- Batte Machinery Zhengzhou Co., Ltd.
- E-mail: email@example.com
- whatsapp: +86 158 38331071
- Tel: +86 371 67991755
- After-sales Tel: +86 371 67997677 / 67997877
- Address:No.11 Changchun Road, High-tech Zone, Zhengzhou, China.
- Analysis of the cold and hot working
- Ten steps to the correct installatio
- Some instructions in the operation m
- Why install a screen changer downstr
- Causes of noise during the operation
- Analysis of Thermal Characteristics
- Introduction of the sealing method o
- batte melt pump manufacturers analyz
- The necessity of applying hydraulic
- The necessity of applying hydraulic
Some instructions in the operation manual of the double-plate fast non-stop screen changer
The dual-plate fast non-stop screen changer has a dual-channel dual-filter screen structure, and the dual screens can work at the same time; when the screen is changed, one screen works and one screen is replaced, which can realize non-stop screen change. For the key contents of the operation manual of the double-plate quick screen changer, Zhengzhou Bart screen changer manufacturer will give a detailed explanation.
1. The screen change position of the double-plate screen changer refers to the position when the slide plate is fully pulled out.
2. The charging position of the double-plate screen changer refers to the position where the net port is completely submerged in the main body of the screen changer and the exhaust port is exposed outside the main body.
3. The working position of the double-plate screen changer refers to the position when the slide plate is fully pushed out.
4. The "start" button on the operating handle of the hydraulic station is a self-locking button, and it will self-lock after being pressed down, and the "stop" button on the operating handle can be disconnected.
5. The "stop" button on the operating handle of the hydraulic station is a jog button. After the jog, the "start" button of the hydraulic station pops up and the hydraulic station is powered off. When released, the "Stop" button will automatically reset.
6. The double-plate quick screen changer has two screens A and B. In the hydraulic station, the "A push", "A pull" and "B push" and "B pull" buttons are all inching buttons. When pushing or pulling the A and B slides, you need to press and hold them. A and B slides are pushing or pulling. During the process, release the button to stop the movement of the skateboard. At this time, the hydraulic station motor is still working, and the "stop" button should be pressed in time to close the hydraulic station.
7. The hydraulic pressure of the double-plate quick screen changer should not exceed 18Mpa. If the pressure of the hydraulic station reaches 18 Mpa, the slide plate of the screen changer still cannot be pushed and pulled smoothly, please shut down the hydraulic station immediately and consult the relevant technical personnel of our company.
Zhengzhou Batte's professional screen changer manufacturer provides screen changers including: plastic extruder screen changer, plastic die head hydraulic screen changer, melt blown double-column hydraulic screen changer, etc. Screen changer manufacturer consultation online: firstname.lastname@example.orgPrevious：Why install a screen changer downstream of the melt pump?
Next：Ten steps to the correct installation of a melt pump